Reviews Creality CR-6 Max
Reviews Creality CR-6 Max
Interested in reviews of Creality CR-6 Max? It got 4.0 out of 5 stars from our customers. Find specific customer reviews of Creality CR-6 Max below. We will appreciate if you also share your experiences with Creality CR-6 Max after purchasing.
User Reviews
Oskar, Lanškroun
Rated 03/03/2024, variant Creality CR-6 Max
Verified purchase
Large dimensions
I'm still struggling with some problems
poor quality electronics
firmware recommended to put into Comuminity firmware immediately after purchase
0 ×Report
Martin, Nový Bydžov
Rated 09/05/2023, variant Creality CR-6 Max
Verified purchase - review from a price comparison website
Large print area, automatic calibration, simple operation and parameter setting.
0 ×Report
Martin, Praha
Rated 23/02/2023, variant Creality CR-6 Max
Verified purchase
TLDR: if you don't need a large area I recommend another product. Putting together a heatbed is a superhuman task. The X-axis came from the factory crooked. Therefore, it was necessary to align the Z-axis motors. The glass on the first calibration point was slightly affected. Print results were of good quality at low speeds. The grip on the glass was also good when I set the zero Z offset correctly. I wanted to know what is the best temperature to filament, so I did a test and it didn't show up on the touch screen. Finally I resigned myself to it, took my old mobile and ran the test via octoprint. It worked back then. After a week, I noticed that the belt under the heatbed was not gripping well. I disassembled the heatbed, straightened the belts and since then the printer has been unusable. On Reddit, people recommended I buy silicone posts that will hold on those bolts so it can be put back on. I haven't tried it but after this experience I won't buy filament from Creality.
Size
In the base with the default Cura profile from the CR6 SE the results look good.
For its size it is still quite portable
After drying, the included filament works suspiciously well
Slow printing
Noisy fan on the power supply, noise similar to a server power supply or a Boeing 737 taking off
The display firmware update is independent of the printer firmware
To update the display firmware, you need to disassemble the display
Heat bed is on 20 plastic posts, which are almost impossible to put back together after disassembly
Temperature changes during printing are not possible without checking the print from an external device, I have not done a temperature test without octoprint
Extruder is difficult to put together, due to poor design
0 ×Report
Ivan, Okna
Rated 08/01/2023, variant Creality CR-6 Max
Verified purchase
Accurate printing after manual calibration and tightening of all screws on the printer. Don't miss a single screw and tighten everything when assembling or you'll worry about automatic calibration before each print and it still won't be OK.
A little slower than the Creality ENDER 3 (which is excellent after the ZD and display upgrade) but with the size of the printer, the size of the print and the resulting products, it's understandable.
0 ×Report
Anonymous customer
Rated 10/03/2022, variant Creality CR-6 Max
Verified purchase
printer cool so far
PETG material does not cooperate in the press with PLA' s satisfaction
0 ×Report
Vladimír, Stupava
Rated 11/11/2021, variant Creality CR-6 Max
Verified purchase
large printing area
accurate printing right after folding, no need to fine-tune parameters
simple and quick assembly
auto levelling
glass plate with decent adhesion and trouble-free removal after printing
quiet stepper motors
large touch screen with clear controls
noisy electronics and power supply fans - especially the power supply
auto leveling of the plate does not take place before each print, for more accurate loading of the plate it is necessary to warm up the plate to the printing temperature, only the nozzle is automatically heated to 120 st.
there is no separate option - a "button" to insert and remove the filament.
SD card reading does not support folders
0 ×Report
