AXAGON HMC-6M2 6in1 Combo Hub, USB-C 5Gbps, 2x USB-A, USB-C, HDMI 4k/30Hz, RJ-45, M.2 SATA, PD 100W

The AXAGON HMC-6M2 COMBO 6-in-1 multiport USB-C 3.2 Gen 1 hub expands your laptop, computer, or phone with four ports and an external box for an M.2 drive. You can easily and quickly connect two USB devices, a Gigabit Ethernet network, an HDMI display, and a SATA M.2 SSD drive to your computer at the same time via the double-sided USB-C connector. You also get the option to power your laptop using Power Delivery technology. The USB-C hub provides you with a simple and compact 6-in-1 docking station for a laptop such as a MacBook Pro.

Input:
• 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-C male connector.
• Backward compatible with USB 3.1 Gen 1 / USB 3.0 and USB 2.0.
• Compatible with Thunderbolt 3.
• USB-C male connector on a permanently attached 18cm cable.

USB Outputs:
• 2x SuperSpeed USB ports, USB-A female connector.
• 1x USB type C Power Delivery port (charging only), USB-C female connector.
• Supports transfer speeds of 5,000 / 480 / 12 / 1.5Mb/s (SuperSpeed / High / Full / Low speed).
• The total throughput/transfer speed is determined by the USB 3.2 Gen 1 interface used (theoretically up to 5Gbit/s).
• The USB-C hub can handle the connection of two external drives simultaneously.

HDMI Output:
• HDMI.
• HDMI A (F) female connector.
• Maximum supported resolution 4K / 4096×2160 at 30Hz.
• For the video output to function, the hub must be plugged into a USB-C port with DisplayPort Alternate Mode (DP Alt Mode) support or a USB-C port with Thunderbolt 3 support. A suitable OS is also required. Without this support, the video output function will not be available.
• HPD (Hot-Plug-Detect) support.
• TMDS (Transition Minimized Differential Signalling) support.
• Full support for HDCP 1.4 and 2.3 (High-bandwidth Digital Content Protection).
• Supports up to 8-channel LPCM audio, compressed audio (AC-3, DTS), and HBR audio formats.
• Supports sampling rates up to 192kHz and up to 24-bit audio – depends on the source and end device, i.e., laptop/phone and TV/monitor/AV receiver.

RJ-45 Output:
• Gigabit Ethernet interface with an RJ-45 connector for UTP or STP cable connection.
• Supported Ethernet interface transfer speeds of 10/100/1000Mb/s.
• Supported specifications: IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T.
• 10/100/1000Mbit/s auto-detection.
• Supports IPv4/IPv6 packet Checksum Offload Engine (COE) to reduce CPU load, including IPv4 IP/TCP/UDP/ICMP/IGMP & IPv6 TCP/UDP/ICMPv6 checksum generation and checking.
• Supports TCP Large Send Offload V1 and V2.
• Supports IEEE 802.1P Layer 2 priority encoding & decoding.
• Supports IEEE 802.1Q VLAN tagging.
• Supports IEEE 802.3az EEE (Energy Efficient Ethernet) - reduction of power consumption at rest.
• Supports Jumbo frame.
• Supports full-duplex transmissions with IEEE 802.3x flow control and half-duplex transmissions with back-pressure flow control.
• Supports Auto MDI/MDIX - crossover detection and auto-correction eliminates the need for crossover cables.
• Supports hardware Cyclic Redundancy Check (CRC) to detect transmission errors.
• Supports pair swap/polarity/skew correction.

Wake-on-LAN feature in various modes:
• Supports sleep mode and remote wake-up via Magic packet, Microsoft Wakeup Frame, Microsoft Wake Packet Detection, ECMA-393 proxZzzy® for sleeping hosts, RealWoW!, and also Link Change wake-up.

Advanced Power Management features:
• The adapter supports advanced power management and advanced power saving, e.g., when the Ethernet cable is disconnected. Supported Power Management technologies include Advanced Configuration Power management Interface (ACPI), Link Power Management (LPM) or IEEE 802.3az EEE (Energy Efficient Ethernet), and others.

Power Delivery:
• Power Delivery 3.0 support - pass-through power for the device from the mains adapter via the USB-C hub.
• Maximum power output via the PD USB-C hub input is 100W - 20V/5A.
• Requires PD support from the device (laptop, phone) and a suitable PD mains adapter.

SATA M.2 Slot:
• SATA M.2 SSD drives.
• Designed for B+M key or B key SATA (AHCI) M.2 SSD cards with no maximum capacity limit.
• NGFF 75-pin B-key slot for SATA M.2 drives.
• Supports M.2 drives of sizes – 2230, 2242, 2260, 2280mm.
• Supports single and double-sided M.2 SSD drives.
• Complies with Serial ATA 3.2 specification (SATA/600), transfer speeds up to 6Gb/s (600MB/s).
• Complies with USB Mass Storage Class specification.
• Supports UASP (USB Attached SCSI) for faster data transfer in Windows 8 and later.
• Supports TRIM to limit the gradual degradation of SSD performance over time.
• Supports booting from an SSD in an external box.

Other features:
• Ability to connect devices while running thanks to Hot Plug support. • Full Plug and Play support. • Sleep mode support.
• Power via USB bus - USB bus power or from a PD charger.
• Durable aluminium body for better hub cooling. A higher hub surface temperature is not a defect - the heat generated by the operation of the hub and the M.2 drive is better dissipated and transferred to the surroundings.
• Two LED indicators - a white LED indicates connection to the computer's USB port (solid light), a blue LED indicates data transfer in the M.2 slot (flashing).
• A high-quality shielded cable guarantees high communication speed and minimal unwanted interference. • Dimensions 123 × 51 × 14mm. • Weight 72g (incl. cable).
• USB cable length 18cm.

Supported operating systems:
• Microsoft Windows 10, Mac OS, Linux, Android and Chrome OS.
Compatibility depends on the operating system used and support from the device manufacturer.
• Note 1: Drivers are included with supported operating systems and are installed automatically. No other drivers need to be installed.
• Note 2: DisplayPort Alternate Mode (DP Alt Mode) is only supported in updated operating systems and also depends on support from the device (laptop, phone).

Package contains:
• USB-C hub with a fixed 18cm cable,
• mounting material,
• multilingual manual